![]() We will be working on a revised version of the Talon locks going forth. This means that the Talon locks will also need to be modified to fit. Available for: Mazda Miata Roadster (1989-2005) Toyota Mr2-Spyder (1999-2007) Sold In Pairs - A pair of Talon locks includes two sets of brackets and bases to secure two OEM latches against tampering. Hard Dog themselves have admitted that the factory strikers need to be trimmed in order to fit their roll bars. Talon Hardtop Security System for factory hardtops with OEM latches. We have had a number of reports that the bar interferes with the mounting of the Talon locks. NOTE: The Talon locks will NOT fit with more recent late 2017 – 2019 Hard Dog HardCore HT roll bars. Tying all of this together is a high quality lock that sits inside the upper claw section, and is fully protected against tampering. Toyota MR2 mk3 Hardtop and fully fitting kit. The slotted mesh design ensures a tight fit, and strong deterrent against prying. system comes with a base plate that is bolted on top of your existing strikers, utilizing your existing OEM bolts, and serves as the anchor to which the upper claw section slides into. This simple approach has allowed us to focus on the more important aspects of the product, like using a higher grade of aluminum, improving the overall look, and fit & finish of the product. features a low profile, sleek and symmetrical design that allow attachment to either side of the vehicle. ![]() We present to you, the TALON Hardtop Security System. Then you get to route the window defroster wire through the soft top sleeve and stuff but that's way too hard to explain without pics.If you value your expensive hardtop, then you need a way to secure it! RetroModern, USA is happy to announce that in conjunction with our partners, we are now able to offer a stylish and effective hardtop security system.Run the seatbelt through the new plastic trim, install the reused plastic plugs into the trim and snap it into place. Denso Upstream Oxygen Sensor for 2000-2005 Toyota MR2 Spyder 1.8L L4 Exhaust or (Fits: Toyota MR2 Spyder) The 1 Seller of Genuine Denso Parts on eBay.If you find anything, please post up as Ive been wanting to do some decent size fender flares for a while. Mine came with 2 sets of bolts for the bottom hole, it didn't seem to matter which I used but I thought that was weird. Other than the two sources you mentioned, the only other place would probably be Ebay for their universal ones, however Im guessing you would still need to do some work to fit them to the spyder body. Install the mounting posts using the supplied bolts.The HT should have come with 2 new trim parts with sections of them cut out to accommodate the hard top mounting posts. Remove the left and right plastic trim parts that the seat belt passes through (unbolt the seatbelt base).On very rare occasion we can find a white top (6 in 14 years. Inquire for other colors, we get them in Black, Phantom Grey Pearl, Solar Yellow, Red, 8M6 Blue, and Silver. Replace them with the stainless latch parts The price is all-inclusive (hardtop, hardware and shipping), but the purchaser is responsible for any import duties (typically 80 in the USA) billed by the carrier (DHL).Remove the rear tabs near the engine hinge that are body colored painted on the Left and Right side.but if no one posts up I can send you a scan of the install info via PM on Sunday. It was a few years ago so I don't remember the actual instructions. Those things above aren't in any instructions but two things I noticed I messed up on the first hard top install. Did it come with all mounting hardware and modified plastic trim pieces?Ģ things on that - when you pull the seatbelts through the old trim pieces, be careful not to pop the retaining rivet off of the seatbelt when you pull it through the plastic trim that is being replaced.Īlso, when installing the new plastic trim using the plastic rivet(s) that holds it in place, do not push too hard otherwise you will 'crease' the trim and create a white mark from pushing to hard (like when you fold a credit card in half, you get that white stress line from bending plastic).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |